 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5
product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 product datasheet strada-fw-n83 series ordering number description family type led color diameter height style optic material holder material fastening status ca12238 ca12238_strada-fw-tape strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - tape ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available ordering number description family type led color diameter height style optic material holder material fastening status C12226 C12226_strada-fw strada-forward lens mx-6 transparent 19.6+15.3 mm 10.9 mm rectangular pmma - glue ready fwhm efficiency cd/lm gerber file asym degrees 92 % - available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 1/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 datasheet strada-fw-n83 lens C12226 materials lens: pmma top view scale: 2:1 19.6 20 c/c 3.2 15.5 11.2 product datasheet strada-fw-n83 series general information - product series especially designed & optimized for mx-6 series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 2/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 22 21 curtain-C12226 20 19 18 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 3/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 17 16 15 14 13 12 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 4/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar-c12086 linear-c12086 curtain-c12086 11 10 9 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 5/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 8 7 6 5 4 3 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 6/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series 2 linear 1 curtain polar 0 october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 7/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-fw-n83 series polar linear curtain october 6th 2011 23:09 copyright ledil oy - subject to change without prior notice - page 8/8 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 22.8.2011 checked by date 22.8.2011 drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 24240 salo finland ah pv 23.8.2011 materials lens: pmma tape: pu foam with psa datasheet strada-fw-n83 assy ca12238 11.4 top view scale: 2:1 19.6 20 c/c 3.2 15.5 |
Price & Availability of C12226
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |